Hello, everyone! nightlights In this discussion I would have the pleasure to teach, how to reuse th

Hello, everyone! nightlights In this discussion I would have the pleasure to teach, how to reuse the old CFL for use as a diode! nightlights So, what do you need? CFL-a-used a low voltage power supply DC-alternator or transformer in ac - a user-a-multinetro wires of various colors to be able to identify the pin First take the CFL, open it, remove the ballast from the bulb , remove the bulb (very carefully) from the plastic "nn Needed this operation" Then once you find yourself detached four pins, divided nightlights into two pairs of two, these two strands are connected to the extremity of the lamp, sciegliete either of these two couples, and settled there with the pond two cables (one red and one blue), and a third cable (black) to one of the two pins on the other end of the bulb. Without this you will end up having three cables (red, blue, and black). Take your power supply, and connect the red cable to the positive (+), and the blue one to the negative (-), in my case I fed the filament to 6V, 2A, "better if you have a variable power supply" Without this there remains the black wire, the black wire is connected nightlights to one end of the alternator you have chosen, and the other end of the alternator is connected to the negative (-) power supply. In series alternator you put a user (LED) and then turn on the power supply, the filament will become orange-red, turn on the alternator, and if the intensity nightlights of the current and the LED should light enough, flashing ( depends freq.dell 'alternator). In theory, the filament nightlights emits electrons have a negative charge, then when c 'a nightlights positive charge on the electrode, the electrons are attracted to them, closing the circuit, as opposed to the thermionic effect nn pass! Hello! nightlights Commented!
Hello! I'll be back to tell you that the only fault I have this diode gas contained in the lamp, so you have to reach a certain voltage, and amperage! nightlights Then there would be some danger:-implosion of the tube-mercury vapor released following the implosion-radiation (in very rare cases) due to the collision of electrons at the metal electrode-burns-the lack of insulation of the conductors Well .. and everything that comes to mind! Hello!
Beautiful and clever!. I would like to ask you something on the board of the TV I found a series of power supplies and transformers, I could use one of those? And what do you mean by pin?
I mean to pin the legs with which it is fed! The flyback has 10. Anyway those transformers have a black core, around?, And n are all transformers, nightlights solenoids, some are simple. Anyway apriti a discussion on this topic, because nightlights you'd be going in ot. Hello! Continue to comment! !! If you have any doubts are available! Hello! At most some photos soon! If you want to use the boob tube as a diode! Nn I have no idea how many volts you have to feed the filament! To me that's a little bulky know .....
then V = RI I'm going to do it on the tv card there are seven or eight processors plus a power supply. nightlights Since I can not destroy the card I'm going to take a transformer 4 diodes nightlights (create a bridge grezz) an electrolytic capacitor and a resistor all to create a power supply. for the rest I have several transformers that I can reuse for the CFL do not have to take it old a new one. I did not understand things, if by 'DC power supply is off and send her into a pair of pins, the other pair of pins what comes out? DC or AC? the transformer connected to the other pin should not go to AC and connected the LED does not work in DC? please could put the schema or a photo of your work?
So the first thing nn I've never heard of the bridge grezz! Cos'? Then during some experimentation I realized that if a pulse of 100v in series with the lamp this is a blink even without powering the filament! And I went into the crisis! nightlights Then, this diode (thermionic valve) allows the passage of current nightlights in one direction then the pass only when the black thread (nn if I'm wrong) there will be a positive charge! To end the current And levy will cc button! For as I said above during an experiment nightlights there were enough 100.130 this is on! But by connecting it in series nightlights with a 100w lamp in series with the 220v nos nothing happened! So I'm in crisis! No I can understand why happen! Now place a scheme! & N